供应康明斯洒水车

康明斯洒水车 【主要技术参数】 产品商标 久龙牌 公告批次 257 产品名称 ALA5160GPSDFL3型绿化喷洒车 产品号 ZK11J4D702B 总质量(Kg) 16000 罐体容积(m3) 9.97 额定载质量(Kg) 9500 外形尺寸(mm) 8400,8150,7800,7550×2490×3100 整备质量(Kg) 6305 货厢尺寸(mm) ×× 额定载客(人) 准拖挂车总质量(Kg) 驾驶室准乘人数(人) 3 载质量利用系数 接近角/离去角(°) 16/12,16/14,16/16 前悬/后悬(mm) 1430/2470,1430/2220,1430/2170,1430/1920 轴数 2 轴距(mm) 4500,4200 轴荷(Kg) 6000/10000 车速(Km/h) 90 其它 罐体有效容积:9.97立方米;介质:水,密度:1000千克/立方米;1、带后操作平台的的整车长度/轴距/罐体外形尺寸(长×长轴×短轴)/后悬/离去角的对应关系为:8400mm/4500mm/5100×2050×1200(mm)/2470mm/12°;7800mm/4200mm/4800×2150×1220(mm)/2170mm/14°.2、不带后操作平台的整车长度/轴距/罐体外形尺寸(长×长轴×短轴)/后悬/离去角的对应关系为:8150mm/4500mm/5400×2000×1160(mm)/2220mm/14°;7550mm/4200mm/5100×2050×1200(mm)/1920mm/16°.侧、后防护装置材料材质为Q235;侧、后防护装置与大梁用螺栓联接,右侧防护部分由工具箱代替;后防护断面尺寸(宽×高)为60×100mm,离地高度为540mm. 【底盘技术参数】 底盘型号 DFL1160BX2 底盘名称 载货汽车底盘（二类） 商标名称 东风牌 生产企业 东风汽车有限公司 外形尺寸(mm) 7790,7490×2370×2760,2840 轮胎数 6 接近角/离去角(°) 20/18 轮胎规格 9.00-20,9.00R20,10.00-20,10.00R20,275/80R22.5 钢板弹簧片数 7/9+6,8/10+8 前轮距(mm) 1880 燃料种类 柴油 后轮距(mm) 1800,1860 排放标准 GB3847-2005,GB17691-2005国Ⅲ 发动机型号 发动机生产企业 排量(ml) 功率(Kw) ISDe180 30

ISDe185 30

ISDe210 30

B190 33

YC6J200-33

EQH180-33 东风康明斯发动机有限公司

东风康明斯发动机有限公司

东风康明斯发动机有限公司

东风康明斯发动机有限公司

广西玉柴机器股份有限公司

东风汽车有限公司商用车发动机厂 4500

6700

6700

5900

6494

4752 132

136

155

140

147

132维护保养

汽车底盘和配套泵的维护保养按相应的使用说明书进行。

（2）车辆使用前应按汽车使用说明书的要求进行磨合。

（3）长途转场托运时，车辆前后左右应有固定防滑装置，且四周留有200mm以上空隙，若自行转场时一般应将前喷嘴和后洒水器卸下以防松动丢失。

（4）经常检查各出液孔、口有无堵塞现象，发现杂物堵塞时应及时清理干净。

（5）每班作业完毕，应清洗油污、管路卷放整齐，清理现场，关门落锁。

（6）车辆长期不用或冬天存放，应放尽罐体、泵内及管路内余水，存放时应停放在车棚内，擦试干净，以避免暴晒雨淋。

洒水车底盘的清洁：离地面最近的底盘肯定是被泥沙弄得一塌糊涂。所以在进行其他部件清洁之前，我们先要对10吨洒水车的底盘进行一个全面的清洁。经过泥泞道路后，10吨洒水车的前后轮毂板上均会沾满黄色的泥浆和小的沙石。在清洁时需用高压水枪放到轮毂板下方，高压水枪的喷水方向朝轮毂板方向，这样才能有效清除附着在轮毂板上的.

洒水车漆面的清洁：完成了底盘的清洁，我们即可对10吨洒水车车身进行清洗。首先，用自来水由上到下地冲洗车漆表面，目的是冲走车身上较大体积的沙石。使用毛巾由车顶到车底轻轻地拭擦。请注意，越靠近底盘的漆面越要小心拭擦，以免爱车车漆被细沙刮伤。

10安全技术要求编辑洒水车每次揭开进料口盖之前，应先打开卸压阀，排出罐内余气，以免发生伤人事故。经常注意洒水车压力表是否工作正常，严防压力表失灵而超压发生罐体爆炸。经常查看安全阀，保证在0.196MPa时开始排气，不得使罐内压力超过0.196MPa。经常查看洒水车转速表工作是否正常，以免超转而损坏空压机及取力箱。并经常清洗转速表探头（此探头在空压机飞轮处）。经常倾听洒水车取力箱及空压机转动声音。若有异常响声，应立即停机排除故障。

maintenance

Auto chassis and the maintenance of the pump according to the corresponding operating instructions.

(2) the vehicle should be in accordance with the requirements of automobile operating instructions before use to get up to speed.

(3) the long transitions checked, the vehicle should be around fixed anti-skid device, and left more than 200 mm gap around, transitions if their own general nozzle before and after the sprinkler should be unloaded loose in case of lost.

(4) regularly check the fluid hole, mouth without blocking phenomenon, and find sundries jams should clean up in time.

(5) per class assignments to complete, should clean oil, line up, clean up the scene, close LaSuo.

(6) the vehicle without or deposited in the winter for a long time, should be put inside the tank, pump and residual water in the pipeline, storage should be parked in the shed, wipe clean, to avoid the sun rain.

Recent sprinkler chassis cleaning: the surface of the chassis is certainly a terrible mess by sediment. So before other parts cleaning, we should first 10 tons of sprinkler chassis for a thorough clean. After the muddy road, 10 tons of sprinkler hub board before and after will be covered in mud and small yellow sand. Need when clean water cannon on the wheel plate, water cannons spray direction, in the direction of the wheel hub board attached to the hub board can effectively remove.

Sprinkler paint surface cleaning: completed the chassis cleaning, we can to 10 tons of sprinkler body wash. First, flush with water by the up and down on the car paint surface, the purpose is to wash away the car on a larger volume of sand. Used towels from the roof to the car bottom gently cleansing. Please note that the closer the chassis paint more careful cleansing, so as to avoid the car was fine sand scratch your paint.

10 safety technical requirements for editing the sprinkler to uncover before feeding flap, should first open the pressure relief valve, drain tank of gas, lest hurt accidents. Often pay attention to the sprinkler pressure gauge is working correctly, fight pressure gauge failure and overpressure tank explosion occurred. Always check valve, to ensure start exhaust when 0.196 MPa, shall not make the tank pressure is greater than 0.196 MPa. Often view the sprinkler tachometer work is normal, in order to avoid super box to damage the compressor and take force. And often clean the tachometer sensor (the probe in air compressor wheel). Often listen to the sprinkler draw power box and air compressor rotation. If there is abnormal sound, should immediately stop the troubleshooting.