12v5a ac电源 移压电源 电源深圳生产厂家

描述(SCOPE):此承认书适应于AAD1060WZ-12型号的工标电源The purpose of the document is to specify the functional requirements of a 60W Working standard switching power supply输入特性(INPUT CHARACTERISTICS):2.1 输入电压(INPUT CHARACTERISTICS):额定电压(Nominal Voltage):110~240Vac调整范围(Variation Range):100~264Vac2.2 输入频率(Input Frequency):额定频率(Nominal Frequency):50-60Hz调整频率(Variation Frequency): 47-63Hz2.3输入电流(Input Current):当输入交流电压为额定值的下限时，输出电压负载满载，输入交流电流1.8A(1.8Arms max At any input voltage and rated,DC output rated load)2.4浪涌电流(Inrush Current):当输出为额定负载，环境温度为25℃，输入240Vac冷态起动电源时的浪涌电流小于30A(30Amps Max. Cold start at 240Vac input, with rated load and 25℃ambient)2.5 AC漏电流(AC Leakage Current): 当输入电压240Vac时，漏电流为3.5mA(3.5mA Max At 240Vac input)3.输出特性(OUTPUT CHARACTERISTICS)3.1输出功率(Power Output)电压Voltage最小负载Min.Load负载Max.Load峰值电流Peak输出功率Output Power12Vdc0A5.0A5.0-5.5A60W3.2负载特性/调整率(Combined Load/Line Regulation):电压Voltage最小空载电压Min. Voltage负载电压Max.Load Voltage线性调整Line Regulation负载调整Load Regulation12Vdc12.36V11.64V±3%±3%3.3纹波和噪音(Ripple And Noise):测试条件：在20MHz带宽内测量纹波需在输出端接一个10uF的电解电容并联一个0.1uF的瓷片电容。(The ripple and noise are as follows when measure with Max.Bandwidth of 20MHz and Parallel 10uf/0.1uf,crossed connected at testing point)电压(Voltage)纹波和噪音(Ripple And Noise Max)12Vdc200mVp-p3.4启动延迟时间(Turn On Delay Time): 当输入115Vac和输出负载时,启动时间为2S 2second Max.At 115Vac input and output Max.Load3.5上升时间(Rise Time): 当输入115Vac和输出负载时时间为40mS 40mS Max.At 115Vac input and output Max.Load3.6保持时间(Hold Up Time): 当输入115Vac和输出负载时,最小保持时间为5mS 5mS Min.At 115Vac input and output Max.Load3.7效率(Efficiency): 当输入100Vac和输出负载时,最小81% 81%Min.At 100Vac input and output Max.Load当输入240Vac和输出负载时,最小83% 83%Min.At 240Vac input and output Max.Load 3.8过冲(Overshoot): 在电源开启或关闭的时候，15% 15%Max.when power supply at turn on or turn off4.保护功能(PROTECTION REQUIREMENT)4.1短路保护(Short Circuit Protection): 该电源适配器在短路解除时，能恢复正常工作(The power supply will be auto recovered when short circuit faults remove)4.2过流保护(Over Current Protection): 过流故障排除后，电源将自动恢复正常工作(The power supply will be auto recovered when over current faults remove)4.3过压保护(Over Voltage Protection):当输出电压超过额定电压时，电源将保护，故障排除后不能恢复正常工作(The power supply will not be auto recovered when faults remove 5.环境条件(ENVIRONMENTAL REQUIREMENT):5.1工作温度(OperatingVoltage Temperature): -10~40℃,满载，正常工作(Full load Normal operation)5.2存储温度(Storeage Temperature): -20~75℃,带外壳(With package)5.3工作湿度：5%(0℃)~90% (40℃) 5.4振动(Vibration): 1.测试标准：国际电工电子委员会Operating:IEC 721-3-3M3 5~9Hz，A=1.5mm加速度(9~200Hz,Acceleration 5m/s2)6.EMC安全要求(SAFETY AND EMI REQUIREMENT)6.1安全：符合CE标准6.2高压(DIELECTRIC STRENGTH)：2000Vdc/5mA/60s7.结构参数(Structural parameters)7.1外壳(Shell):110*78*38mm